Code requirement
The applicable rules depend on the county, permit dates, work performed, local amendments, and equipment instructions. The newest national model code is not automatically the code that governed an older installation.
Hawaii-focused inspection findings: what they mean, why they matter, and the usual next steps.
Browse 52 common inspection flags. Select any thumbnail to open the finding and its usual solution. Every finding includes a labeled issue-and-fix comparison. Enlarge any diagram for a closer look. Similar symptoms can have different causes; repairs depend on an on-site assessment.
An inspection can identify a safety concern without declaring a code violation. We explain the visible condition, why it matters, and a practical next step.
The applicable rules depend on the county, permit dates, work performed, local amendments, and equipment instructions. The newest national model code is not automatically the code that governed an older installation.
“Grandfathered” is shorthand, not a blanket safety approval. Some work that complied when installed may remain under existing-installation provisions. Age alone does not establish original compliance, and damaged or hazardous conditions still need attention.
An upgrade can be worthwhile even when no retroactive requirement has been established. Adding GFCI protection at a wet-location outlet is a good example: reduced shock risk matters independently of the age of the house.
Replacement devices, new circuits, remodeling, and changes in use can trigger requirements for the affected work. This does not automatically require updating the whole home. A licensed trade and the authority having jurisdiction determine what applies to the project.
Honolulu DPP announced the 2020 NEC with State amendments as its interim electrical code for new permit applications from March 14, 2024. The published Chapter 17 still references an earlier edition. Confirm the applicable edition and amendments with DPP for the actual project; do not apply an internet checklist as a property-specific ruling.
DPP interim electrical code notice ↗ · Honolulu electrical code and existing-installation provisions ↗
We check accessible systems thoroughly within the agreed scope. A home inspection is not a permit inspection, a full code audit, or proof that concealed work was approved.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Lifted, cracked, or missing covering may leave the roof vulnerable to water entry.
A broken tile, displaced shingle, or worn roof membrane can expose the layers below. The visible covering is only part of the water-shedding assembly; the repair may also involve underlayment or fastening. An accessible inspection cannot establish the condition of every concealed layer.
A roofing contractor repairs or replaces affected materials and checks the surrounding assembly. Widespread wear may call for a broader repair plan.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Staining or drips may appear near vents, skylights, valleys, or wall intersections.
Flashing guides water around changes in the roof plane and penetrations. A ceiling stain may be remote from the actual opening because water travels along framing. Sealant over a stain or a roof joint does not establish that the underlying water path has been corrected.
Locate the entry point and repair the flashing or affected roof assembly before refinishing interior stains.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Split sealant around penetrations can admit water.
Sealant is a maintenance item, but some joints should be protected by properly installed flashing rather than a bead of caulk alone. The roofer should select a compatible repair for the roof material and inspect the adjacent assembly for concealed deterioration.
Have a roofer restore the appropriate flashing and seals.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Covered vents can limit air movement.
Insulation, stored items, or alterations may obstruct designed attic airflow. Ventilation should be considered together with roof design, moisture sources, and insulation. Simply adding more openings can create other problems if the assembly is not evaluated as a whole.
Clear obstructions and assess the ventilation arrangement.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Moist exhaust can wet attic materials.
Bathroom fans move humid air; terminating that air inside the attic can wet sheathing and framing. The duct connection, exterior hood, and discharge location matter. Any damp materials should also be assessed after the exhaust route is corrected.
Have the exhaust routed to a suitable exterior termination.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Leaves and debris can interrupt roof drainage and send water over the gutter edge.
Overflow can soak fascia, siding, or ground beside the foundation even when the roof covering is sound. Debris removal is the first step; recurring overflow may indicate inadequate capacity, slope, or discharge rather than a cleaning issue alone.
Have debris cleared and damaged, loose, or poorly draining gutter sections corrected.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Roof runoff or surface water may collect against the building.
Water should have a controlled route away from vulnerable building areas. A downspout extension can help in some situations, but the full path matters: moving runoff onto a walkway, neighboring property, or another low spot is not a complete solution.
Improve discharge paths and assess whether extensions, surface grading, or drainage work are appropriate.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Separated joints discharge runoff against the building.
An open joint releases concentrated water at a single location. The contractor should restore connections and supports and confirm where water goes at ground level. Nearby staining or deterioration may need repair after the runoff problem is resolved.
Reconnect or replace damaged sections and secure them.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Standing water remains in sections after rain.
Sagging runs or incorrectly positioned outlets can leave water standing in a gutter. Standing water adds weight and can accelerate corrosion or leakage. Repairs should address supports and the intended flow path rather than only sealing a dripping seam.
Adjust supports and slope or replace distorted sections.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Surface runoff is directed toward walls or supports.
Paving, landscaping, and additions can change drainage over time. The right correction may involve grading, drains, or management of roof runoff. Excavation near supports and changes affecting adjacent properties require a properly planned approach.
Evaluate grading and drainage improvements for the site.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Movement at a guard, post, or connection can affect safety.
Guards and posts must resist everyday leaning and movement. Wobble can reflect loose hardware, concealed decay, or a weak connection to the framing. Tightening a visible screw may not correct a deteriorated supporting member.
Keep the affected area out of use until assessed. A qualified contractor repairs the connection or replaces damaged components.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Coastal exposure and moisture can deteriorate deck hardware and framing.
Salt air and repeated wetting are especially relevant on Oahu. Rust stains can be an early clue, but the remaining metal and surrounding wood determine repair needs. Replacement fasteners and connectors must suit the treated wood, exposure, and connection design.
Assess the extent of deterioration and replace affected wood, connectors, and fasteners with compatible materials suited to the exposure.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Unstable surfaces can create a trip or fall hazard.
A loose or soft walking surface can conceal deterioration below. Repairs should consider the condition of joists and attachment points as well as the boards. Isolate an unsafe area until the supporting assembly has been checked.
Replace damaged boards and restore secure attachment.
Conceptual explanation · have the actual condition evaluated before selecting a repair
The deck-to-house connection has visible gaps or inadequate attachment.
The ledger transfers deck loads to the building. Missing or questionable fasteners, gaps, or water entry at this joint can affect the whole deck. A surface patch does not establish adequate anchorage; concealed attachment may require specialist evaluation.
Have the connection and water protection evaluated before repair.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Loose steps or missing graspable rails affect safe access.
Uneven risers, loose treads, and missing graspable rails can make a short flight of stairs hazardous. Applicable dimensions and guard requirements depend on the installation and governing rules. Repairs should improve the complete path of travel, not just its appearance.
Repair the stair assembly and provide suitable handrails.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Some crack patterns, displacement, or ongoing changes warrant further evaluation.
Crack size alone cannot distinguish settlement, shrinkage, or structural movement. Displacement, location, related sticking doors, and evidence of change provide context. An engineer may recommend measurements or monitoring before selecting a repair.
Have the cause evaluated before choosing a repair. Cosmetic patching alone does not resolve structural movement.
Conceptual explanation · have the actual condition evaluated before selecting a repair
A noticeable change in floor level or deflection may have several causes.
Uneven floors can result from original construction, deterioration, altered framing, or support movement. A general inspection documents visible clues; it does not calculate load capacity. Evaluate the cause before leveling floors or adding supports.
Evaluate supports, framing, and related moisture conditions; design repairs around the identified cause.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Damp soil or standing water affects supports and materials.
Groundwater, runoff, and leaking pipes require different remedies. Persistent dampness can deteriorate materials and encourage wood-destroying organisms. Dry conditions on inspection day also do not establish that seasonal water entry never occurs.
Identify the source and correct site drainage or plumbing leaks.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Framing or posts contact damp ground.
Wood-to-soil contact keeps material exposed to moisture and can make pest activity harder to see. Correcting the clearance does not restore already damaged wood. Assess the remaining member and arrange a separate pest evaluation where appropriate.
Evaluate deterioration and correct contact and clearance conditions.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Cuts, splits, or removed supports may affect load paths.
Notches, holes, removed posts, or split members can change how loads are carried. Visible damage warrants review of the affected assembly. Repairs should follow an appropriate design rather than relying on an improvised brace.
Have an engineer evaluate the affected framing and specify repairs.
8 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Two conductors share a terminal that is not listed for that conductor arrangement. Two wires alone do not establish a defect; the terminal rating matters.
A termination must be listed for the number, type, and size of conductors installed. Some terminals accept two conductors and many do not. Incompatible terminations can loosen or overheat; evaluation requires the equipment markings and condition, not just counting wires.
An electrician verifies the equipment listing and corrects incompatible terminations.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Required shock protection is absent or does not respond correctly to testing. An ordinary-looking receptacle may already be protected by an upstream GFCI or breaker.
GFCIs reduce shock risk by interrupting a circuit when current leaks from its intended path. They do not replace grounding, overcurrent protection, or safe wiring. Protection may be at the receptacle, an upstream device, or a GFCI breaker; see the location guide below.
An electrician verifies protection and provides suitable GFCI protection where needed.
The following is a residential location guide using the 2020 NEC as a reference, not a finding that every older outlet must be retrofitted. The applicable edition, amendments, circuit characteristics, exceptions, and permit history must be checked.
Appliances, pools, spas, and some other equipment have separate provisions. An electrician should check the actual installation rather than assume this location list covers every case.
An ordinary-looking outlet can be protected by another GFCI receptacle or a GFCI breaker. A “GFCI protected” sticker alone does not prove the device works. Accessible testing helps establish protection at the time of inspection, subject to the wiring and testing limitations.
Lack of protection may be reported as a safety improvement without asserting that the original work violated its applicable code. An electrician can verify existing protection and provide a suitable retrofit. GFCI protection does not add an equipment-grounding conductor or fix unrelated wiring defects.
Read codes versus older installations ↑
Eaton: 2020 NEC GFCI location guide ↗ · CPSC: household electrical safety ↗
Conceptual explanation · have the actual condition evaluated before selecting a repair
Scorching, discoloration, or unusual heat can indicate a failing connection or damaged equipment.
Heat damage may come from a loose connection, poor contact, or an overloaded or failing component. A new faceplate hides the symptom without fixing its source. Avoid the affected device until an electrician determines the extent of damage.
Stop using the affected outlet and have an electrician evaluate and repair the cause.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Receptacle testing indicates a wiring concern.
An open ground means the test did not confirm an effective equipment-grounding path; reversed polarity indicates a connection concern. Older two-wire circuits require a different evaluation from damaged modern wiring. GFCI protection can reduce shock risk but does not create an equipment ground.
An electrician verifies the finding and corrects the wiring.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Wiring connections or energized parts may be exposed.
Enclosures help keep people and combustible materials away from connections. Missing covers, unsecured boxes, and splices outside enclosures need evaluation. The correct repair depends on the box, wiring method, and environment.
Have proper enclosures and covers installed.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Unfilled openings allow access to panel interiors.
Unused openings in a panel should have appropriate closures. Improvised tape or an incompatible filler may not provide the intended protection. Panel interiors and any suspected energized parts should be handled by an electrician.
Have an electrician fit suitable listed closures.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Cables are vulnerable to movement or damage.
Wiring methods must suit their location and exposure. A cable crossing a storage area, sharp edge, or outdoor surface may need protection as well as support. An electrician should check for damage and select an appropriate repair.
Have wiring secured and protected as appropriate.
Conceptual explanation · have the actual condition evaluated before selecting a repair
The device moves, cracks, or does not retain plugs.
A moving device can strain its connections, and worn contacts may not grip a plug properly. The box, mounting, wiring, and device condition should be checked together. Replacing only the decorative cover may leave the underlying defect.
Have the damaged device and its mounting repaired.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Moisture can collect on cool surfaces and affect nearby finishes.
Condensation forms when moist air meets a cool surface. In Hawaii, air conditioning and indoor humidity can contribute; exterior water entry can look similar. Identify when and where moisture appears before choosing ventilation, dehumidification, or window repairs.
Address indoor moisture and ventilation. Persistent wetness may also need investigation for water entry.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Discolored, swollen, or deteriorating finishes can be signs of moisture exposure.
A dry stain records past wetting but does not prove the source is repaired; a normal moisture reading is only a snapshot. Roofing, plumbing, windows, and condensate systems may all be possible sources. Correct the source before repainting or replacing finishes.
Find and fix the water source, dry affected areas, then repair damaged materials. Significant mold or water damage may need specialist help.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Operation or locking is impaired.
Sticking may reflect hardware wear, paint buildup, frame distortion, or movement in the opening. Windows intended for emergency escape warrant particular attention. Repair should restore the intended operation and latching, not simply force the sash closed.
Adjust or repair the window and check surrounding damage.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Persistent haze is trapped inside insulated glass.
Fogging between panes usually differs from condensation on the room-side surface. A failed insulated-glass seal affects visibility and insulating performance. A glazing contractor can assess the sealed unit without assuming that the whole window frame needs replacement.
Have the glass assembly evaluated for replacement.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Gaps occur at tubs, showers, or splash-prone joints.
Sealant at a shower or tub is a serviceable joint, not the complete waterproofing system. Repeated gaps, loose tiles, or soft material nearby can indicate a deeper issue. New caulk should not conceal damaged substrate or an unresolved leak.
Dry and assess the substrate, then renew suitable sealant.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Water may come from a connection, accessory, or the tank itself.
Connections, valves, pans, and the tank itself can all be leak sources. A leaking storage tank generally cannot be repaired like a loose fitting. Have the actual source identified and assess adjacent materials rather than assuming visible surface rust tells the full story.
Have a plumber identify the source. Repairable connections can be corrected; a leaking tank may require replacement.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Changing performance, unusual noise, or inconsistent temperature can indicate a service need.
Output varies with demand, incoming water temperature, controls, sediment, and component condition. Solar systems and backup elements may need separate evaluation. A short inspection operation cannot establish available hot water under every household demand.
A qualified technician assesses the heater and recommends maintenance, component repair, or replacement as appropriate.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Hot discharge is not safely directed from the relief valve.
The temperature-and-pressure relief valve is a safety device. Its discharge needs an appropriate path where hot water can leave safely. A missing line, obstruction, or cap is a safety concern; a plumber should evaluate the full installation.
A plumber corrects discharge piping; never cap the relief outlet.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Discharge may indicate a valve or system problem.
Discharge may relate to excessive temperature, pressure, thermal expansion, or a faulty valve. Stopping the drip by plugging the outlet defeats the safety function. Have the cause evaluated promptly by a qualified plumber.
Have temperature, pressure, and valve operation assessed promptly.
Conceptual explanation · have the actual condition evaluated before selecting a repair
A leak may damage nearby finished areas.
A pan limits some damage only when its location and discharge route are appropriate. It does not prevent a leak or contain every possible failure. A plumber should assess the surrounding finishes, installation requirements, and a safe discharge destination.
Assess whether a pan and safe drain path are needed.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
Small recurring drips can waste water and damage nearby materials.
A drip can originate at a fixture cartridge, supply hose, valve, or drain connection. Identify whether it occurs under pressure or only during fixture use. Repair the source and check cabinetry or finishes for damage before closing the area back up.
Repair the faulty fixture part or leaking connection after identifying the source. Dry and assess affected cabinetry or finishes.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Water may continue flowing into the bowl or overflow rather than stopping after a flush.
A failed flapper, fill valve, or other internal part may keep water moving after the flush. Some leaks are quiet and waste water without wetting the floor. Repair should restore normal fill and shutoff operation and confirm the leak has stopped.
Identify the faulty flush/fill component and repair or replace it; a plumber can confirm the cause.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Water backs up or drains sluggishly.
One slow drain may have a local obstruction, while several affected fixtures can suggest a larger drainage problem. A general inspection cannot see the entire buried sewer. Persistent or widespread symptoms may justify separate drain or sewer-camera evaluation.
Have the blockage and drainage arrangement evaluated.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Movement or moisture is visible at the floor connection.
Movement can damage the seal at the toilet connection. Water at the base may also originate higher on the fixture, so diagnosis matters. A plumber should evaluate the flange, mounting, seal, and any softened floor before resetting the toilet.
Have the seal, mounting, and floor condition repaired.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Deterioration or moisture appears at valves and hoses.
Corrosion is a clue to age, moisture, or material condition, but it does not by itself identify the leak source. Disturbing a deteriorated valve can cause failure. Have the affected assembly repaired and confirm accessible shutoffs are suitable for service.
Replace affected components and assess water damage.
5 common inspection flags
Illustrative example · not a client inspection photo
Conceptual explanation · have the actual condition evaluated before selecting a repair
A restricted filter, dirty coils, or another equipment issue can reduce performance.
Low airflow and poor cooling can reflect filters, coils, ducts, controls, or refrigeration problems. These symptoms are not enough to diagnose a refrigerant shortage. An HVAC technician should evaluate performance under suitable operating conditions.
Maintain filters per the manufacturer; have an HVAC technician assess coils, blower operation, and other causes if performance remains poor.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Water collecting near the indoor unit can indicate a condensate drainage problem.
Condensate is normal; leaking into a wall, ceiling, or floor is not. Drain routing, blockages, pans, and pumps should be evaluated together. Correct the cause and inspect wet finishes rather than simply emptying a pan.
Have the drain, pan, and related components inspected and the blockage or leak corrected.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Restricted filters reduce airflow.
Filter condition affects airflow and cleanliness of the equipment. Use the size and type specified for the system; a more restrictive filter is not automatically better. Cleaning or replacement intervals depend on the equipment and actual use.
Clean or replace filters per equipment instructions.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Bare cold piping can sweat and lose efficiency.
Cold piping can collect condensation when insulation is missing, damaged, or open at joints. That moisture may damage nearby finishes. Restore suitable insulation and have any oil staining or suspected refrigerant leak evaluated separately.
Have damaged insulation renewed with suitable material.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Debris limits heat transfer and air movement.
Coils need unobstructed air movement to reject heat. Salt exposure and debris can contribute to deterioration in coastal settings. Cleaning methods and clearances should follow the equipment guidance so the coils and electrical components are not damaged.
Have coils cleaned and proper clearance restored.
4 fireplace inspection flags
For Hawaii homes with a fireplace, we examine accessible visible components within the agreed scope. A home inspection does not include lighting a fire or a specialist chimney inspection.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Deposits or debris can obstruct the flue.
Wood combustion can leave combustible deposits. A rarely used fireplace can also have nests or debris; lack of use does not establish a clear flue.
Have a chimney professional inspect and clean as needed before use.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Gaps, cracks, or deteriorated surfaces are visible.
The firebox and flue help contain combustion products and heat. Hidden liner damage may require camera inspection beyond the home inspection.
Do not use a suspect fireplace until a chimney specialist evaluates and repairs it.
Conceptual explanation · have the actual condition evaluated before selecting a repair
A damper is stuck or smoke staining suggests poor venting.
A damper that moves does not by itself prove safe draft. Fuel type, appliance instructions, and venting configuration matter, especially for converted units.
Have a fireplace or chimney specialist evaluate the assembly and restore intended operation.
Conceptual explanation · have the actual condition evaluated before selecting a repair
Trim, stored items, or finishes appear close to heated surfaces.
Clearances depend on the listed appliance, fireplace construction, and applicable requirements. A decorative alteration can change the original safe arrangement.
Keep the fireplace out of service until a specialist confirms clearances and corrects unsafe materials.
An inspection helps document visible conditions and identify where further evaluation may be useful.